发夹式换热器管束流致振动数值模拟研究

运用计算流体力学方法,采用ANSYS CFX软件对发夹式换热器的壳侧流场进行了三维数值模拟。流场计算中采用多孔介质模型对管束区域进行简化,分析了壳侧流场的速度分布,结果表明:直管段部分的流体湍流强度大于弯管段,且外层管束所在区域为高流速区,受流体冲刷严重。结合流场信息,通过功率谱生成随机激振力,采用ABAQUS软件模拟计算了湍流激振下管束的振动响应,结果显示管束的面外均方根位移远大于面内位移,且弯管部分的振动位移最大。该研究结果可为发夹式换热器的性能分析和优化设计提供参考和依据。     

煤磨热风管道改造的效果

中联万基水泥有限公司4500t/d熟料生产线采用SCLW4-12×13.4第四代篦冷机,煤磨热风取风口和余热发电AQC热风取风口在篦冷机同一对称位置,煤磨与余热发电系统存在争风现象,开停煤磨对余热发电系统影响较大。通过从废气管道处开孔,加装管道和电动阀,与热风管道汇合通往煤磨沉降室,调整相应阀门开度,可以控制入煤磨烟气温度,这样不但提高了余热发电量,而且提高了煤磨产量,同时也降低了窑头排风机的负荷,降低了熟料生产电耗。     

磁流变阻尼器抑制转子系统振动试验

针对大型旋转机械通过临界转速时振动过大及运行中故障频发等问题,搭建转子试验台,模拟启停机过程和碰摩、不对中故障。不改变原有支撑形式,安装自主设计的磁流变阻尼器,在不停机的情况下,试验研究阻尼器抑制转子通过临界转速时振动过大及各类故障振动。试验结果表明,阻尼器可以有效抑制转子系统临界转速附近的振动,降幅在60%以上;转子发生碰摩或不对中故障时,阻尼器可以降低其高倍频振动。     

Covalent triazine framework with efficient photocatalytic activity in aqueous and solid media

Covalent triazine frameworks (CTFs) have been recently employed for visible light-driven photocatalysis due to their unique optical and electronic properties. However, the usually highly hydrophobic nature of CTFs, which originates from their overall aromatic backbone, leads to limitations of CTFs for applications in aqueous media. In this study, we aim to extend the range of the application media of CTFs and design hybrid material of a CTF and mesoporous silica (SBA-15) for efficient photocatalysis in aqueous medium. A thiophene-containing CTF was directly synthesized in mesopores of SBA-15. Due to the high surface area and the added hydrophilic properties by silica, the hybrid material demonstrated excellent adsorption of organic molecules in water. This leads not only to high photocatalytic performance of the hybrid material for the degradation of organic dyes in water, but also for efficient photocatalysis in solvent-free and solid state. Furthermore, the reusability, stability and easy recovery of the hybrid material offers promising metal-free heterogeneous photocatalyst for broader applications in different reaction media.     

Research on the identification performance of UHF RFID system considering the correlation of cascaded channel

The identification rate of UHF RFID system was restricted by multipath propagation effects.The system identification performance was studied considering the correlation coefficient between forward and reverse channels.Based on the generalized Rician fading channel model,the analytical expression of identification rate was derived under independent,full correlation and correlation cases.Compared with the existing analysis,the proposed uniform calculation formula of identification rate was for any correlation coefficient and kinds of channel conditions.The numerical computation and Monte-carlo simulations show that the influences of different correlation coefficients,channel conditions,sensitivity and distance on the identification rate.     

15CrMoG钢棒材表面缺陷机理分析和工艺改进

分析得出,棒材表面细小纵裂纹和表面裂口缺陷产生于铸坯加热之前,且与结晶器弯月面保护渣有关。利用Thermo-Calc热力学软件计算15CrMoG钢凝固相变过程,结合亚包晶钢连铸凝固特点综合分析15CrMoG钢棒材表面缺陷的产生原因和产生机理。结果表明:15CrMoG钢在固相线温度附近发生包晶反应L+δ→γ和包晶转变δ→γ,不仅导致初生坯壳生长不均匀,而且加剧P、S元素在凝固前沿的偏析。而初生坯壳不均匀是导致棒材表面缺陷根本原因。棒材表面细小纵裂纹产生于结晶器内坯壳薄弱处,经过二冷和轧制工序在夹杂物和硫偏聚处扩展长大。棒材表面裂口缺陷是初生坯壳不均匀导致结晶器内液面波动大,造成铸坯夹渣所致。通过控制[C]0.16%～0.17%、[S]≤0.005%、保护渣碱度1.2、熔点≥1200℃、粘度≥1.0Pa·s,260 mm×30mm铸坯水量150 m³/h,拉速0.5 m/min等措施,裂纹合格探伤合格率由原45%提高至98%。     

高强不锈钢绞线网与ECC黏结-滑移关系模型

高强不锈钢绞线网与ECC的黏结是二者协同工作的基础，且黏结 滑移关系模型是其黏结性能的综合反映，故通过对17组51个高强不锈钢绞网增强ECC薄板试件进行单边拉拔试验，研究横向钢绞线间距、纵向钢绞线直径和相对锚固长度等因素对钢绞线网在ECC中黏结性能的影响规律。试验结果表明，横向钢绞线的设置可使黏结破坏由脆性破坏转变为延性破坏；高强不锈钢绞线网与ECC的黏结滑移曲线可分为5个阶段，分别为上升段、微降段、延性强化段、下降段和残余段。基于试验结果，对钢绞线网在ECC中的黏结破坏特征和黏结 滑移机理进行分析，在相关黏结-滑移关系模型的基础上，提出钢绞线网与ECC的黏结 滑移关系模型，并进行模型参数分析。所提模型及模型参数计算公式与试验结果吻合良好，能较好地反映钢绞线网与ECC的界面黏结滑移特征。     

Do funded papers attract more usage?

Research funding has been seen as one of the most important resource in the reward system of science. And usage of publications denotes an interesting perspective of user behavior in scientific communication. This study aims to address the relationship between funding and Usage Count, which is a new metrics item established on the platform of Web of Science. Full records of 300,010 articles published in 2013 were downloaded in October 2015, and divided into six disciplines, including information science library science, education educational research, economics, computer science, materials science, and chemistry. Seven indicators were proposed to measure the impact, including Funding rate, Citation per paper, Usage rate, Usage per paper, Citation difference, Usage difference, and Conversion rate. It concluded funding has impact on usage and citation, and funded papers attract more usage, but varying in different disciplines. Usage Count can be used in the extension of citation metrics but with limits. This study originally engages with usage metrics and detected that there is positive correlation between usage and funding.     

03Cr18NiMoN节镍双相不锈钢的热变形行为及热加工图

关键词：双相不锈钢； 流变曲线； 本构方程； 热加工图     

基于DoG检测图像特征点的快速二进制描述子

针对SIFT描述子实时性差和传统二进制描述子对尺度、旋转和视角变化鲁棒性差的问题,本文通过优化采样模式和添加灰度差分不变量比较测试进行改进,提出了一种鲁棒性更高的二进制描述子。首先,设计了一种尺度关联、编号标记的采样模式;然后,旋转采样模式中各采样点到特定位置,确保描述子尺度、旋转不变性;接着,分析了采样点点对模式对描述子的影响,选择使用机器学习训练后的128对采样点对;最后,选择灰度值比较测试及梯度绝对值和比较测试构建二进制描述子。实验中采用DoG检测图像关键点,结果表明:本文提出的描述子在描述子构建和描述子匹配上比SIFT描述子分别快84%和67%;在有视角变化的图像匹配上,准确率比传统的二进制描述子高3%~5%,召回率平均要高30%以上。本文提出的特征点描述方法适用于时间要求高的图像匹配领域。